Building materials · Practical application guide
Pigment Calculations for Cement-Based Building Materials
Build a usable color formula by separating binder dosage, pigment blends and the water carried by liquid preparations.

Start with a dosage you can calculate
For conventional cement-based color development, 2%, 3% and 4% powder trials provide a useful first comparison when the selected grade permits that window. LANXESS Europigments gives a 2–4% recommendation on cement or lime for its Bayferrox/Oxined construction pigments and advises against exceeding 5% for those products. These are named-product references, not a guarantee for every pigment. Powder-pigment guidance
Identify the material first. A cement ornament, lime render, polymer-modified mortar and fired ceramic cannot share one universal recipe. For a proprietary bagged product, obtain permission to add external pigment. For your own formulation, preserve the established binder, sand and additive ratios during the first color series.
Work from binder mass rather than total batch mass
Dry pigment mass = reference binder mass × selected percentage / 100. State exactly which binder ingredients count. For example, Davis’s cementitious dosage convention includes cement, lime and other specified cementitious materials, while excluding aggregate and sand. Binder definition
| Trial batch with 20 kg reference binder | Pigment percentage | Powder required |
|---|---|---|
| Uncolored control | 0% | 0 g |
| Lower candidate | 2% | 400 g |
| Middle candidate | 3% | 600 g |
| Higher candidate | 4% | 800 g |
These are calculated weighing quantities. Sand and water remain those of the approved base formulation. A 100 kg dry-mortar batch containing 20 kg reference binder would need 600 g at 3%, not 3 kg. Its binder fraction must be known rather than guessed from bag weight.
Calculate blended colors and liquid substitutions separately
Suppose a laboratory-selected blend contains 80% red and 20% black powder by mass. At the 600 g total-pigment level, weigh 480 g red plus 120 g black. This example demonstrates blend arithmetic; it does not predict a particular brown. Keep total pigment constant when comparing blends, then adjust total loading only after selecting the preferred hue.
For a hypothetical liquid preparation containing exactly 50% dry pigment and 50% water, delivering 600 g pigment requires 1,200 g preparation and contributes 600 g water. Subtract that water from the batch water. Actual preparations can contain other solids: use pigment content and water content from their data, not an assumed 50% or an iron-oxide purity number. Europigments separately identifies slurry dosage and carrier-water adjustment. Liquid preparation guidance
Use a controlled charging and forming sequence
- Identify every container with pigment grade, lot and actual weighed mass. Check scale zero with an empty weighing container; keep powder out of drafts and use the material’s dust-control precautions.
- Select a loading route appropriate to the material. For example, Sakrete directs its own Cement Colors to be dispersed in batch water before the dry mix. Do not assume a different powder or mixer requires the same route. Product-specific wet premixing example
- Mix identical-size batches with a recorded timer. Inspect a smear for streaks and dry lumps before forming the sample. Do not add extra pigment or water merely to improve the wet appearance.
- Reproduce the intended thickness, mould face or trowel finish. Mark the underside, then cure all comparison samples together under the material’s prescribed conditions.
Approve the dry product and find the cause of defects
Compare equally dry specimens, then make a fresh repeat of the preferred formula. Keep the original control visible: a changed uncolored base is useful evidence that the cement, sand or finish has changed. Wet and dry material can look substantially different. Wet-to-dry appearance
| Result | Investigate before adding pigment |
|---|---|
| Uniform but dull shade | Gray binder, aggregate color, unsuitable hue |
| Dark specks | Pigment agglomerates or mixer residue |
| Different batches | Weighing, binder source, water correction, finish |
| Pale surface deposit | Moisture and salts rather than dosage alone |
Record color, fresh consistency and the product’s required strength or bond results separately. The selected pigment formula should not replace the original product acceptance checks. Send FUXIN the dry target, calculation sheet and preferred trial when requesting grade confirmation and a quotation.
Technical references
- LANXESS Europigments: powder and liquid instructions
- Davis Colors: Mix-Ready dosage basis
- Sakrete: Cement Colors technical sheet
Independent technical guidance used for this application overview. These references are not FUXIN project case studies or a substitute for a grade-specific technical data sheet.
