Request a Quote
Menu ☰

Cement products · Practical application guide

Cement roof tiles. Color & production.

Convert a selected pigment dose into plant quantities and follow it through extrusion, curing and any surface coating.

Illustrative pigment application: Cement products.
Illustrative application image. Confirm the finished shade with physical samples.

Decide which part of the roof tile you are coloring

This roofing application concerns cement roof tiles and fittings, not fired clay. Identify whether color is inside the tile body, in a surface coating, or both. Keep separate formulas and retained samples for those layers. A coating can change the initial appearance enough to conceal a mismatch in the body recipe.

Marley’s published production description illustrates the distinction: a pigmented cement-and-sand mix is formed and cured, then tiles may receive a water-based surface coating. It is an example of another manufacturer’s process, not a FUXIN project or a universal operating specification. Tile manufacturing reference

Translate the selected body-color recipe into plant weights

Use a pigment grade documented for cementitious tile production. First obtain the candidate loading and its precise reference binder definition. Davis’s construction-color guidance illustrates binder-based rather than aggregate-based dosage. Construction pigment denominator

For a hypothetical approved 3% dry-pigment loading, the calculations are:

Declared reference binder per batchPigment at 3%
Laboratory: 10 kg0.30 kg
Pilot: 50 kg1.50 kg
Production: 250 kg7.50 kg

These are scale-up examples, not a complete tile recipe. Keep the plant’s validated sand grading, binder composition and additives fixed. If limestone filler or another addition is present, state whether the pigment specification includes it in the denominator. Never silently count all powder as cement.

Correct water before chasing a shade change

Record aggregate moisture and any water arriving with pigment dispersion. As a mass-balance example, 105 kg wet sand containing 100 kg dry sand plus 5 kg free water contributes 5 kg water to the mix; compensate in the plant water calculation. The moisture value is hypothetical and must be measured in production.

For liquid color, use its stated pigment and water contents. A suspension may need agitation before dosing; equal kilograms of slurry and powder are not equivalent. Scholz discusses liquid-color use in fine cementitious and roof-tile applications, while the actual preparation’s data must determine its conversion. Roof-tile pigment forms Keep water correction independent of the color operator’s visual judgment.

Follow a trial through the production line

  1. Produce an uncolored control and the chosen body-color trial with recorded raw-material lots and pigment weights. Check the feeder and mixer for color retained from a previous run.
  2. Use the actual forming equipment. Record the normal mixing and extrusion settings, observing edge definition, surface tearing and handling strength. A smooth hand-cast coupon cannot test extrusion behavior.
  3. Label tiles by batch and position in the trial. Include any fitting made on a different line so its appearance can be compared with the main tile.
  4. Run the plant’s established curing and demoulding route. Keep identified uncoated tiles; send the remaining samples through the specified coating process.
  5. Assemble a small display of equally dry tiles and compare both body and coated appearance. Record the coating lot and application conditions separately from pigment data.

Use two appearance checks and one technical release

Compare the uncoated bodies first. If those match but coated tiles differ, investigate the surface treatment rather than changing body pigment. Then verify the finished product’s specified dimensional, mechanical and water-related requirements through the tile producer’s quality program.

ObservationLikely investigation
Whole batch is lighterBinder source, actual pigment and water
Local streaksDispersion or dosing carryover
Different rack positionsCuring and moisture differences
Coated tiles alone differCoating and application record
White film during storageMoisture and deposits

Marley explains that efflorescence can resemble fading; it does not mean every deposit on every roof has the same cause. Roof-tile appearance diagnosis Send FUXIN the chosen body formula, dry samples and forming results. Request evidence for any proposed weathering or reflectance claim separately; ordinary color selection does not prove it.

Technical references

Independent technical guidance used for this application overview. These references are not FUXIN project case studies or a substitute for a grade-specific technical data sheet.

Sample inquiry