Decorative mortar · Practical application guide
Decorative mortar.Ratios & coverage.
Build a pigment trial around your cementitious finish, then measure the material needed for its actual surface texture.

Fix the finish and the pigment basis
This workflow is for a cementitious decorative mortar that you formulate or are permitted to pigment. Keep its approved cement, lime, sand and performance additives unchanged while selecting color. For a proprietary finish, confirm external-pigment permission first; an acrylic coating needs a different colorant assessment. Decide whether the target is a smooth, floated or textured finish before making samples.
For its Bayferrox/Oxined powder pigments in concrete or mortar, LANXESS Europigments gives a 2–4% reference range on cement or lime. Use it to plan an initial comparison only if the selected FUXIN grade supports that window. The cited manufacturer advises against exceeding 5% for its products; this is not a universal limit. Powder-pigment instructions
Weigh a useful three-step color trial
The example below uses 8.00 kg of declared cement/lime binder per batch. Sand, additives and water remain those of your established decorative-mortar recipe. If its documented pigment basis excludes a particular constituent, recalculate before weighing.
| Sample | Powder/binder | Dry pigment | Purpose |
|---|---|---|---|
| Control | 0% | 0 g | See the uncolored base |
| A | 2% | 160 g | Lower color loading |
| B | 3% | 240 g | Middle comparison |
| C | 4% | 320 g | Check the benefit of more pigment |
These are calculated sample quantities, not a complete mortar formulation. Do not deduct pigment from cement. For a separately selected 80:20 two-powder blend, the 240 g total becomes 192 g plus 48 g. The blend proportion is an arithmetic example, not a promise of a particular shade. Keep blend ratio fixed when comparing total loading.
Why package percentages differ: a LaHabra system example uses a 16 oz color pack with 90 lb of its specified tint base. That is about 1.11% of the whole dry base, not of cement. It does not authorize replacing the pack with the same mass of FUXIN powder. Color-pack denominator example
Mix and apply your trial
- Prepare the real substrate and basecoat on a labeled trial panel. Mark separate sample areas and use the same basecoat condition for each. Keep the pigment and binder weighing records together.
- Use the charging sequence established for your finish and pigment form. Measure all mixing water. Check a thin smear for pigment dots before application; repeating the same short cycle will not fix incomplete dispersion.
- Record mixing, any prescribed resting period and remixing separately. As a product-specific example, Sakrete Finish Coat Stucco specifies approximately 3–4 minutes mixing, 2 minutes resting and 1 minute remixing. Use those times only for that product, not as a universal recipe. Example mixing schedule
- Apply at the finish system’s permitted thickness. Reproduce the actual float or trowel movement, including a corner and a planned work boundary. Keep finishing water controlled; do not retemper stiffened material.
- Follow the prescribed curing and protection. Include any final sealer on the sample before appearance approval.
Measure coverage instead of guessing
Weigh usable mortar before and after covering a measured panel, accounting separately for dropped material. Applied mass / area = application consumption. For example, 2.4 kg applied over 0.5 m² equals 4.8 kg/m². At that observed rate, 100 m² needs 480 kg before your measured waste allowance. This is a calculation example; the actual value comes from your texture trial.
Record whether the figure means wet mixed mortar or dry bagged material. Do not order 480 kg of dry powder solely from a wet-mortar figure. Repeat coverage measurement for a deeper texture. It can change both material demand and the visible shade even when pigment dosage is unchanged.
Compare equally dry finishes and troubleshoot
Evaluate the panel straight on and in side lighting. Check color together with texture, soundness and the specified bond performance. If a pale target looks muddy, compare a separate white-cement base rather than continually raising pigment. A change of binder is a new formulation trial.
| Problem | Check first | Next controlled comparison |
|---|---|---|
| Dark trowel patches | Overworking or inconsistent pressure | Fixed tool and finishing stage |
| Light batch boundary | Water and timing at the join | Measured water and planned boundary |
| Colored specks | Agglomerates or mixer residue | Improved dispersion and cleaning |
| Color shifts with texture | Aggregate exposure and shadows | Same formula, standardized finish |
Sakrete’s finish guidance identifies over-floating and inconsistent water as causes of appearance variation. Finish-control background Send FUXIN the chosen dry sample, binder basis, A/B/C results and texture description when requesting a matching pigment grade.
Technical references
- LANXESS Europigments: Powder pigment instructions
- Sika: Color-pack denominator example
- Sakrete: Finish Coat Stucco technical data
Independent technical guidance used for this application overview. These references are not FUXIN project case studies or a substitute for a grade-specific technical data sheet.
