3D printed cementitious materials · Practical application guide
3D-printed cement. Color & extrusion.
Track pigment basis, material age, bead geometry and layer interfaces instead of relying on a cast color chip.

Treat color as a material-and-process change
A pigment trial for extrusion printing must be carried through the printer. NIST’s research roadmap describes the interaction between fresh properties, hardened properties and printed geometry. A cast color tile may screen a shade, but it cannot demonstrate pumpability, layer stability or the performance of a printed object. Begin with the printer/material supplier’s qualified baseline and approval to evaluate an added pigment. NIST: 3D Concrete Extrusion Research Roadmap
Use system-approved levels, then calculate precisely
The NIST sources do not establish a universal iron-oxide dose for printable cementitious materials. Keep the printer/material system’s accepted window. The following 1%, 2% and 3% values are calculation examples only, not proposed safe operating limits. Include an unpigmented reference in the qualification program.
Define the reference binder before weighing: cement plus only the additions counted as cementitious by that formulation. Sand, fibers, water and nonreactive filler do not automatically belong in that denominator. If a proprietary system provides an explicit complete-premix dosing basis, use it as documented rather than estimating the hidden binder fraction.
Calculate batch and production quantities
| Declared binder | If 1% is approved | If 2% is approved | If 3% is approved |
|---|---|---|---|
| 2 kg screening batch | 20 g | 40 g | 60 g |
| 15 kg pilot batch | 150 g | 300 g | 450 g |
| 60 kg production binder | 600 g | 1,200 g | 1,800 g |
For a hypothetical pilot containing 15 kg binder within 25 kg original dry premix, 300 g pigment is 2% of binder and 1.2% of original dry premix. Name the denominator whenever reporting a percent. Scaling that approved formula to 60 kg binder multiplies all recipe quantities by four; pigment becomes 1.2 kg.
For a verified 50%-pigment, 50%-water suspension, the 300 g dry-pigment equivalent would require 600 g suspension and contribute 300 g water. This is arithmetic, not permission to introduce liquid color into a system that cannot accommodate it. Reconcile the carrier with the qualified water budget. Liquid-color accounting principle
Print the same diagnostic object for every trial
- Choose a small nonstructural test path containing a straight run, corner and a controlled restart. Use the same nozzle and programmed geometry.
- Record the mixing sequence, pigment mass, complete water/admixture ledger, material temperature and time zero. Include any stoppage before pumping.
- At the same defined material ages, measure the system’s chosen consistency indicator. Compare uncolored and pigmented material using the identical method.
- Log pump settings and available pressure/current signals. Measure bead width and height at marked locations; photograph corner behavior and restart defects.
- Keep layer interval and print speed fixed during the color comparison. If a setting must change, identify that as a separate process trial rather than silently modifying the original candidate.
Make the measurements interpretable
| Measurement | Record alongside it | What comparison answers |
|---|---|---|
| Consistency | Age, temperature and test method | Does the colored material change with time? |
| Extrusion signal | Pump setting and nozzle | Has transfer behavior changed? |
| Bead width/height | Location and commanded geometry | Is the deposited shape repeatable? |
| Layer interval | Actual timestamp per pass | Are interfaces made under matching conditions? |
| Dry color | Cure, orientation and surface moisture | Does the final visible shade repeat? |
A measured 31 mm bead compared with a 30 mm target is about 3.3% wider; this is a calculation example, not an allowable tolerance or a suggested nozzle dimension. Use the process limits established for the actual printer and material.
Check interfaces and color transitions
NIST emphasizes layer-interface performance and the limits of applying conventional-concrete testing directly to printed material. Printed-interface assessment Arrange the required representative sampling and tests with the responsible technical team. A good-looking print and a strong cast cube do not by themselves qualify the printed component.
For a color change, identify transitional output separately and record the material quantity and elapsed time until the accepted shade stabilizes. Do not assume a hopper change produces an immediate nozzle change. Use the equipment’s approved changeover and waste-handling procedure; never clear a blocked line by improvising pressure or access.
Symptoms and next actions
| Observation | Check | Action |
|---|---|---|
| Extrusion becomes irregular | Age, dispersion or transfer conditions | Stop outside limits; repeat a controlled trial |
| Bead spreads more | Water ledger and material response | Review the formulation without undocumented dilution |
| Color bands at restart | Residence time and transition material | Separate and assess start/stop output |
| Layer separation | Interface condition and print interval | Hold the candidate for technical testing |
Keep the accepted print, toolpath and batch data together. Send FUXIN the precise material system and comparative records so pigment selection remains linked to a tested printing process.
Technical references
- NIST: 3D Concrete Extrusion Research Roadmap
- NIST: Long-Term Performance of Additively Constructed Structures
- LANXESS Europigments: Product-use guidance
- Concrete Countertop Institute: Integral Pigment Types
Independent technical guidance used for this application overview. These references are not FUXIN project case studies or a substitute for a grade-specific technical data sheet.
