Art and DIY · Practical application guide
Concrete art & DIY. Small-batch color.
Use gram-level calculations, check scale error and build a repeatable color library for decorative cement castings.

Choose a suitable material and an economical first screen
Use a known cement-based casting material that permits added pigments. For a decorative color screen, consider 0%, 1%, 2% and 4% dry-pigment trials only within the chosen product’s permitted range. The Concrete Countertop Institute describes a typical 0.5–5% of total cementitious mass range for its countertop context; the nonzero trial steps are an exploratory selection within that interval, not a FUXIN craft formula. Pigment-range background
This page does not cover gypsum, epoxy or polyester resin. A bag called craft concrete may contain undisclosed fillers and additives; establish the binder basis before calculating a percentage.
Use a small-batch calculation table
Dry pigment grams = dry reference binder grams × percentage ÷ 100. These are separate batches with known binder content; retain the base mix’s approved sand, water and admixture proportions.
| Trial | 500 g binder | 1,000 g binder | 2,000 g binder |
|---|---|---|---|
| 0% control | 0 g | 0 g | 0 g |
| 1% | 5 g | 10 g | 20 g |
| 2% | 10 g | 20 g | 40 g |
| 4% | 20 g | 40 g | 80 g |
For example, 1 kg of cement plus 0.2 kg of a qualifying cementitious addition gives 1.2 kg binder: a 2% trial needs 24 g dry pigment. A 1.2 kg bag of complete casting premix does not necessarily contain 1.2 kg binder. If the manufacturer instead supplies a dose per kilogram of premix, use that documented method.
Check the scale before trusting a tiny dose
A 1 g error in a 5 g pigment dose is 20%; the same 1 g error in a 40 g dose is 2.5%. These calculated errors explain why a very small batch can be harder to reproduce. Choose adequate scale resolution, check it with a suitable known mass and use a separate tared cup. Display resolution alone does not prove accuracy. Small-mass weighing discussion
Avoid spoon measures. If the required mass is too small to weigh reliably, enlarge the whole test batch or use a verified concentrate with a documented concentration. Do not improvise an unmeasured water slurry.
Mix one trial at a time
- Clean the container and mould, label the sample and record the material lots. Follow the material safety sheets for dust and wet-cement protection.
- Weigh the base material, pigment and mixing water separately. Use the pigment/casting-system charging order. Where dry incorporation is approved, first distribute color through the dry ingredients; where a liquid is used, re-homogenize and include its carrier water.
- Keep the same mixer or paddle, batch load and timed cycle for each candidate. Note scraping or interruptions. Inspect the mixed paste for specks and streaks before casting.
- Fill the same mould geometry. Keep the placement and air-release method constant. Do not rescue one sample with extra water.
- Use the casting material’s demoulding and cure instructions. Record the actual times rather than comparing a fresh sample with an older one.
Approve the dry and finished sample
Cast a simple color chip and one small piece containing the intended fine detail. Keep one as cast; sand or seal its companion only if that is the planned final finish. The Countertop Institute distinguishes pigment-screening samples from specimens intended to represent other textures. Sample-purpose guidance Observe the pieces together after comparable curing and drying. Record the finish before approving it, then make a second independent batch to confirm the recipe.
A practical problem-solving table
| Symptom | Check | Action |
|---|---|---|
| Large color change between tiny batches | Weighing error and binder denominator | Increase batch size or improve the scale |
| Specks or dark streaks | Powder clumps or insufficient incorporation | Repeat with a controlled dispersion step |
| Missing fine detail | Mould, release and casting consistency | Test the base casting process without changing color |
| Unexpected darker finished surface | Sealer or polishing effect | Compare finished and unfinished companions |
Keep a recipe card with actual grams, water, equipment, mixing cycle, mould, cure and photographs. Pigment alone does not establish food-contact, candle or heat suitability. For a repeat order or color match, send FUXIN the dry sample, casting material identity and weighed trial records rather than a wet photograph alone.
Technical references
- Concrete Countertop Institute: Integral Pigment Types
- Concrete Countertop Institute: Making Your Own Color Samples
- Concrete Countertop Institute: Digital Scales and Small-Mass Errors
- LANXESS Europigments: Product-use guidance
Independent technical guidance used for this application overview. These references are not FUXIN project case studies or a substitute for a grade-specific technical data sheet.
