Lightweight wall panels · Practical application guide
Lightweight Wall Panels: Color & Moisture Trials
Identify the colored layer, calculate its pigment separately and keep lightweight-aggregate water distinct from mixing water.

Identify what makes the panel lightweight
A lightweight wall panel may use porous aggregate, a cellular cementitious core or a layered construction with a separate facing. These systems do not share one pigment recipe. State where color is required: the entire panel, a cementitious skin or a surface coating. The workflow below is for a producer evaluating color in a cement-bound material, with detailed moisture checks particularly relevant to lightweight aggregate systems.
Choose a dose only for the defined cementitious layer
For an ordinary cement-based facing already approved as part of the panel, a 2%, 3%, 4% dry-pigment color screen can use the same manufacturer-context reference as conventional concrete. Solomon’s stated range applies to its dry integral colors; it does not qualify a foamed core, aerated product or proprietary lightweight panel. Conventional concrete reference
Keep an uncolored control. For cellular or proprietary core systems, use their accepted pigment levels and the calculation method below rather than treating this facing ladder as a universal recipe.
Calculate the face and core separately
| Colored material | Declared binder mass | 2% | 3% | 4% |
|---|---|---|---|---|
| Facing bench batch | 2 kg | 40 g | 60 g | 80 g |
| Facing pilot batch | 8 kg | 160 g | 240 g | 320 g |
| Qualified whole-body trial | 20 kg | 400 g | 600 g | 800 g |
At a selected 3%, an 8 kg-binder facing needs 240 g pigment even if its uncolored core contains another 20 kg binder. Only the material being colored enters that face calculation. If the entire composite is to be colored, each distinct material requires its own formula and validation. The table does not prescribe layer thickness or a structural composition.
Declare whether the binder denominator includes supplementary cementitious materials. Keep aggregate, nonreactive filler and process water outside a cementitious-basis calculation. An unknown complete dry premix mass is not a substitute for the required binder value.
Keep absorbed and free water apart
ESCSI’s internal-curing guidance distinguishes lightweight aggregate’s absorbed moisture from external free water; its specification says absorbed water in that system does not contribute to mixing water. Follow the method for the actual aggregate rather than subtracting all measured moisture. Absorbed-water distinction
Arithmetic example: if a validated moisture procedure identifies 0.30 kg free water on the aggregate and the target batch-water contribution is 3.00 kg, the remaining separately added water is 2.70 kg before other carrier corrections. If an approved liquid color additionally contributes 0.10 kg water, it becomes 2.60 kg. These calculations assume the qualified water target is unchanged; they are not a recommended water/binder ratio.
Make a panel-section trial
- Record aggregate conditioning, moisture test result and the exact water correction. Prepare baseline and colored batches with matched material condition.
- Follow the qualified mixing sequence. Measure the process consistency and fresh density using the plant’s method, then note any change after pigment addition.
- Produce the actual face/core arrangement, return and edge. Record the application interval and the intended thickness of each approved layer.
- Keep forming, cure and conditioning traceable. Cut a spare section to inspect face continuity and unintended core exposure.
- Repeat the selected color and check the specified panel properties. ESCSI treats density, strength and workable placement together for lightweight concrete. Performance context
Troubleshooting by symptom
| Symptom | Check | Next action |
|---|---|---|
| Color and workability both drift | Aggregate moisture correction | Repeat with measured free water |
| Density shifts after coloring | Batch masses, air/core process | Investigate under the qualified panel method |
| Edge shows a different color | Facing continuity or exposed core | Review representative detail and specification |
| Only one face is pale | Moisture, form contact or surface treatment | Compare equally conditioned matching faces |
| Cracking or layer separation | Composite compatibility | Hold production for technical evaluation |
A pigment adjustment cannot establish core stability or facing bond. Do not use a thicker colored skin to conceal a defect without reviewing the panel design. For foamed systems, aggregate prewetting guidance does not replace the supplier’s own foam and density controls.
Keep the approved recipe usable
Retain the reference panel section, binder and pigment masses, water ledger, density/consistency records and cure history. Link appearance approval to the required product tests. Send FUXIN the panel architecture, color location, material route and weighed comparison results. This makes the inquiry about a specific colored layer and process rather than an undefined lightweight wall panel.
Technical references
- Solomon Colors: Dry Integral Colors, dosage and ready-mix instructions
- ESCSI: Guide Specification for Internally Cured Concrete
- ESCSI: Guide Specification for Structural Lightweight Concrete
- The Concrete Society: Colour variation
Independent technical guidance used for this application overview. These references are not FUXIN project case studies or a substitute for a grade-specific technical data sheet.
