Powder coatings · Practical application guide
Powder Coatings: Mixing & Cure Guide
Calculate powder-formula changes without disturbing the binder system, then track color through both manufacturing and cure.

Set the formula basis before assigning a percentage
For powder coating, express pigment as a mass fraction of the complete powder formulation unless the formula explicitly specifies another basis. That total includes resin, crosslinker, pigments, extenders and additives. It is different from an additive percentage on pigment. Keep the established resin/crosslinker balance fixed while reviewing a color change. Pigment does not replace curing agent.
The sources below do not establish one universal iron-oxide loading across powder chemistries and shades. Use the selected pigment’s approved starting point or an existing qualified formula. The calculation examples illustrate weighing and comparison; they are not a ready-to-extrude formulation.
Calculate the final-powder target
Illustrative approved-target calculation: if the formulator selects 3% pigment in 1,000 g final powder, weigh 30 g pigment and retain 970 g of the correctly rebalanced remaining formula. Do not simply add 30 g to 1,000 g of existing powder and call that 3%: 30/1,030 × 100 = 2.913%.
For addition to a fixed unpigmented base mass B, required pigment P = f × B ÷ (1 − f), where f is the desired final fraction. With 1,000 g base and f = 0.03, P = 30.928 g. This arithmetic changes final batch mass and does not resolve binder-volume, flow or film-property effects.
Keep resin and crosslinker accounting visible
Example accounting only: assume a previously qualified recipe uses 700 g combined resin/crosslinker, 20 g other additives, 20 g pigment and 260 g extender per 1,000 g. A proposed increase to 30 g pigment would leave 250 g extender if that were the formulator-approved balancing component. Keep the resin and crosslinker individually at their original amounts.
| Component group | Illustrative control | Proposed color change |
|---|---|---|
| Qualified resin + crosslinker | 700 g | 700 g |
| Other additives | 20 g | 20 g |
| Pigment | 20 g | 30 g |
| Extender balance | 260 g | 250 g |
| Total | 1,000 g | 1,000 g |
These assumed quantities are not a recommendation to substitute pigment for extender. Different density and surface area can alter pigment volume and flow. Have the formulation owner decide the correct balance, then use this ledger to ensure the decision is reproduced rather than accidentally changing the cure chemistry.
Process a trial through the full powder route
- Make a traceable control and candidate premix. Weigh small ingredients on suitable balances and use powder-handling controls.
- Premix, extrude, cool and prepare powder through the validated grinding/classification route. TIGER identifies premixing, extrusion and micronization as the manufacturing stages. Powder manufacturing route
- Record extruder settings, throughput and actual material temperatures. Avoid treating an extruder setpoint as the pigment’s complete thermal history.
- Keep the classified powder size distribution comparable between trials. Otherwise application and finish differences can obscure the colorant comparison.
- Apply to equivalent prepared panels at the product-specified film thickness. Cure with a recorded workpiece temperature/time profile. Allnex defines cure using object/metal temperature for the relevant system, not merely oven air temperature. Object-temperature cure definition
Assess extrusion exposure and oven exposure separately
Retain an extrusion chip, uncured powder and cured panel from each trial. If the chip changes but the subsequent cure does not, investigate the manufacturing stage. If change appears during baking, compare the qualified cure histories and pigment grade. LANXESS’s heat-stable yellow range includes distinct chemistries; its named-product limits must not become generic yellow-oxide limits. Grade-specific heat stability
Any overbake comparison must stay within a laboratory plan agreed for the complete powder system. Do not deliberately overheat production material to find a pigment limit.
Troubleshooting and release tests
| Observation | First check | Repeat test |
|---|---|---|
| Specks in film | Premixing, extrusion, contamination | Inspect powder and cured panel |
| Shade changes after baking | Workpiece profile and pigment grade | Matched nominal-cure panels |
| Gloss or flow changes | Formulation volume and dispersion | Compare equal-thickness films |
| Different application behavior | Powder size distribution and handling | Controlled spray comparison |
Evaluate cured color, opacity, gloss and surface texture alongside specified adhesion, cure and durability tests. Compare color using the agreed geometry and acceptance method. Color tolerance practice Keep a retained panel; loose powder color is not the release standard.
Prepare the technical brief
Send FUXIN the binder family, existing pigment fraction, full dose denominator, extrusion history, workpiece cure profile and target panel. Include whether the product must tolerate reclaimed powder or another heat history. Qualify those routes before releasing the selected grade.
Technical references
- TIGER Coatings — Architectural handbook: Powder coating technology
- Allnex — Powder coating resins product guide
- LANXESS — Heat stable inorganic yellow pigments
- ASTM International — ASTM D2244-25: calculation of color tolerances and color differences
Independent technical guidance used for this application overview. These references are not FUXIN project case studies or a substitute for a grade-specific technical data sheet.
