Prefab wall panels · Practical application guide
Prefabricated panels. Facing color control.
Calculate the visible mixture separately and transfer the selected color through full-size mock-ups and repeat production.

Agree the panel surface and viewing conditions
Define whether the visible panel is smooth as cast, textured, ground or exposed aggregate. State whether color is in the full panel or a qualified facing mixture. PCI’s color-and-texture guidance treats aggregate, form and finish as coordinated design choices. Select an initial sample with the architect and precast producer, then agree the normal viewing position and acceptable visual range before production. PCI: Color and Texture Selection Guide
Use a limited initial color comparison
For an ordinary cementitious architectural face mix, 0%, 2%, 3% and 4% dry-pigment candidates provide a compact initial screen where the grade permits them. The nonzero levels lie within Davis’s stated typical 1–5% cementitious-content range for its integral colors. This is manufacturer-context guidance, not a universal FUXIN panel formula. Dose and denominator reference
Keep cement, additions, sand and aggregate fixed during the first comparison. If the chosen hue cannot be achieved economically, run a separate white/gray cement or aggregate study rather than changing several variables in one batch.
Calculate the facing rather than the whole panel
| Reference binder in colored mixture | 2% pigment | 3% pigment | 4% pigment |
|---|---|---|---|
| 5 kg color-screen batch | 100 g | 150 g | 200 g |
| 20 kg mock-up facing | 400 g | 600 g | 800 g |
| 100 kg production facing | 2.00 kg | 3.00 kg | 4.00 kg |
At 3%, a facing containing 20 kg qualifying binder needs 600 g dry pigment. If an uncolored backing contains another 80 kg binder, do not calculate 3% against the combined 100 kg and put 3 kg into the facing. That would make the facing addition 15% on its own binder, not 3%. This example illustrates a denominator error; it does not prescribe a facing/backing composition.
Declare the included cementitious additions and exclude aggregate and water. If the panel is colored throughout using one qualified concrete mixture, calculate on that mixture’s total reference binder instead. Keep different mixtures identified independently.
Move from a chip to a production mock-up
- Use small color chips to reject unsuitable hues, recording actual grams, material sources, water correction and mixer cycle.
- Produce the preferred mix in a representative panel with a broad face, return, reveal and joint. Include all specified finishes.
- Use the production mould and qualified release procedure. Record cast date, mould ID, application method, placement sequence and demoulding time.
- Make a second independently batched panel on another production day. Keep cure and finishing records so differences can be investigated.
- Place the samples in the intended orientation and obtain written appearance approval. PCI’s workshop emphasizes realistic expectations and the transition to full-size samples. Sample-to-production guidance
Record the controls that matter on a façade
| Control | Record | Keep comparable |
|---|---|---|
| Materials | Binder, aggregate and pigment lots | Source and declared proportions |
| Mould contact | Mould/liner and release record | Face condition and preparation |
| Cure | Temperature/time and stripping age | Approved cycle |
| Finish | Exposure or processing method | Selected endpoint |
| Assessment | Panel age, moisture, light, orientation | Agreed comparison conditions |
| Layout | Panel and batch positions | Actual adjacent appearance |
The Concrete Society identifies form, stripping and curing differences as contributors to shade variation. Panel-surface variation A batch sheet alone therefore does not explain every façade mismatch. Preserve production photographs showing each panel before and after finishing.
Judge the arrangement, including permitted repairs
Stand representative panels together and inspect returns, joints and changes in finish. Compare surfaces at similar age and moisture condition. PCI notes that textured finishes can make subtle variation less apparent than smooth finishes; changing the specified finish still requires the designer’s agreement. Finish-consistency context
Trial a permitted cosmetic repair on a spare representative piece and record its appearance after the intended cure and finish. Keep the accepted range samples protected and accessible. Do not judge replacement panels only against an old photograph of the completed façade.
Troubleshooting and release
| Symptom | Check first | Action |
|---|---|---|
| Entire panel lighter | Facing dose, binder and water records | Repeat under matched conditions |
| Shade changes with mould area | Release, leakage or surface condition | Correct mould preparation in a new trial |
| Adjacent panels differ | Age, cure, source or finishing | Compare full records before changing pigment |
| Patch is conspicuous | Repair formulation and texture | Qualify repair on a spare piece |
| Facing/backing defect | Composite and production compatibility | Hold for technical review |
Complete required panel, connection and building-envelope checks for the approved system. Link visual approval to that product’s qualification records. Send FUXIN the dry master, facing calculation and mock-up results for grade matching, and review any later material or process change before resuming production.
Technical references
- PCI: Color and Texture Selection Guide
- Davis Colors: Architect’s Guide
- PCI: Acceptability of Appearance, Samples and Mockups
- The Concrete Society: Inherent colour variation
- Georgia/Carolinas PCI: Architectural Precast FAQs
Independent technical guidance used for this application overview. These references are not FUXIN project case studies or a substitute for a grade-specific technical data sheet.
