Request a Quote
Menu ☰

Sand-based permeable pavement · Practical application guide

Sand-based paving. Color & water-flow checks.

Keep the colorant inside an approved sand-binder formulation and measure water flow without mistaking a color sample for drainage certification.

Illustrative pigment application: Sand-based permeable pavement.
Illustrative application image. Confirm the finished shade with physical samples.

Identify the binder and the water path

Sand-based permeable products can use resin-coated sand, cementitious material or a composite of different layers. Obtain the real cross-section and formulation ownership before choosing pigment. Determine whether water travels through the unit, through joints or through both. Dense ordinary mortar and a proprietary permeable face cannot share an assumed color recipe.

An original study of composite permeable bricks combines a resin-sand surface with a cementitious base and reports trade-offs between formulation changes and physical behavior. It does not establish an allowable pigment dose for another product. Composite-brick research

Calculate on the approved layer’s declared basis

There is no universal iron-oxide percentage for this category. Use only a dose approved for the actual binder. The following hypothetical 1% example demonstrates the difference between possible denominators; it is not a recipe or a recommended concentration.

Written basis in a hypothetical formulationReference amountColorant at 1%
Resin binder only0.50 kg5 g
Sand mass10.00 kg100 g
Cement in a separate approved cementitious layer2.00 kg20 g

Calculating on sand rather than the specified 0.50 kg resin would give twenty times the intended pigment. The cement-layer example is another formulation, not an alternative way to dose the same surface. Keep the component ratio of any reactive binder fixed and obtain permission for the pigment’s chemistry and moisture content.

Make paired specimens without changing the pore structure

  1. Use an uncolored control and the authorized candidate. Record sand grading, binder lot, actual pigment mass and moisture condition.
  2. Disperse color through the developer’s approved method. Do not add more binder simply because the pigmented mixture feels different; that would change a second variable.
  3. Form equal specimens using the same thickness, pressure or compaction and curing route. Identify layers separately in a composite unit.
  4. Inspect for pigment clumps, uneven coating and visible surface closing. Keep part of the sample set dry for color comparison.
  5. Test the specified mechanical and water-flow properties through the product laboratory. A visually attractive surface that loses required permeability is not an acceptable color result.

Use simple flow arithmetic only as a comparison record

A laboratory may compare the volume collected over a fixed time while holding specimen area, thickness, water head and conditioning constant. Flow rate Q = collected volume / time.

For a hypothetical paired observation, the control passes 900 mL in 10 minutes and the pigmented specimen passes 800 mL in 10 minutes. The corresponding rates are 90 and 80 mL/min; candidate/control flow is 88.9%. This arithmetic is not a permeability coefficient, a standardized test result or an acceptable limit. The project’s method and criteria must determine whether the material passes.

RecordKeep identical or document
Sample geometryArea, thickness and layer arrangement
ConditioningCure age, moisture and temperature
Water setupHead, supply and collection method
Observed flowVolume and elapsed time
AppearanceDry, wetted and redried surface

Check maintenance and surface changes

Do not sprinkle pigment onto a finished permeable surface or seal it merely to improve color. Both introduce an uncontrolled surface change. Evaluate the developer’s approved sediment and maintenance procedures on the complete system. CMHA’s permeable-pavement guidance explains sediment-related loss of infiltration for joint-draining pavers, a distinct system whose details should not be transplanted into a resin-sand unit. Maintenance context and system distinction

FindingNext investigation
Flow falls after pigmentationDispersion, binder film and forming
White or colored wash-offSurface integrity and material release
Composite layers separateInterface and cure compatibility
Color changes only when wetCompare after equal redrying

Keep color, flow and strength results together. Send FUXIN the binder chemistry, approved dosage basis and paired sample results. Do not turn these trials into claims of water purification, permanent anti-clogging behavior or environmental suitability without the appropriate finished-product evidence.

Technical references

Independent technical guidance used for this application overview. These references are not FUXIN project case studies or a substitute for a grade-specific technical data sheet.

Sample inquiry