Colored asphalt repair materials · Practical application guide
Colored asphalt repairs. Pigment & binder trials.
Use hot-asphalt dosage references only for an approved hot-asphalt formulation, and keep cold repair systems on their own instructions.

Identify the existing pavement and repair technology
Find out whether the original color comes from conventional bitumen, a pigmentable clear binder or a surface coating. Then identify the repair system: hot asphalt, cold-applied material, emulsion-based mix or a resin treatment. A hot-asphalt powder instruction cannot authorize changes to a packaged cold repair. For a proprietary repair, use the manufacturer’s approved color route.
Clean a representative part of the existing surface by its approved method before selecting the target. Decide whether the repair should match the original supplied color or the present weathered appearance. Keep a dry physical reference; a wet patch can conceal a substantial mismatch.
Use the binder to set a realistic color range
Procter Johnson’s asphalt guidance gives typical pigment levels of 2.5–5% of total coated macadam, while its clear-binder example uses 1–3% of total mix. These are that supplier’s references, not universal FUXIN recommendations. Conventional dark bitumen and clear binder cannot be expected to produce the same bright shade at the same pigment loading. Binder-specific pigment references
Shell’s documented clear-binder application also pairs binder selection with a selected aggregate color. This supports evaluating the whole material combination rather than treating the pigment as the only color variable. Binder and aggregate example
Calculate a limited clear-binder hot-asphalt trial
For a manufacturer developing an approved clear-binder hot-asphalt repair, a grade-permitted comparison within the cited 1–3% window can be calculated as follows. Here total mix means final mixed mass including pigment. Confirm the supplier’s convention before batching.
| Final sample mass | Pigment level | Pigment | Other ingredients in the approved design |
|---|---|---|---|
| 10 kg | 1% | 100 g | 9.90 kg |
| 10 kg | 2% | 200 g | 9.80 kg |
| 10 kg | 3% | 300 g | 9.70 kg |
This table does not prescribe the binder-to-aggregate ratio or authorize arbitrary replacement of filler. The asphalt technologist must maintain a valid complete mix design. At an already accepted 2% final-total dose, a 500 kg run contains 10 kg pigment. Do not interpret this as 2% of bitumen alone, and do not apply the table to cold repair material.
Test mixing and the repair interface
- Use the actual binder and aggregate lots, with an uncolored control where appropriate. Verify pigment compatibility with the intended heating exposure and processing time before the production trial.
- Follow the pigment and asphalt-system charging sequence. Procter Johnson’s reference introduces pigment with or just after binder and specifies a minimum 45-second mix for its described process. That is a supplier example, not a universal plant cycle. Mixing reference
- Form and compact specimens through the approved repair process. Record actual temperatures and timing, without borrowing a temperature from another pigment grade.
- Make an interface sample with representative existing pavement, using the repair system’s specified preparation and geometry. Leave repair depth and construction design to the project specification.
- Judge appearance after the required cooling or curing stage, then check the specified adhesion, cohesion, deformation and friction performance.
Troubleshoot the match instead of adding powder blindly
| Problem | Investigate |
|---|---|
| Patch is uniformly too dark | Binder shade and target selection |
| Color is weak despite more pigment | Binder masking, aggregate and dispersion |
| Streaks remain | Charging sequence and mixing |
| Patch crumbles or detaches | Complete repair formulation and installation |
| New patch differs after wear | Exposed aggregate and aging |
For cold or emulsion-based repair, obtain its own formula permission and process data before any pigment trial. Preserve the selected specimen and batch record for repeat repairs. Send FUXIN the exact binder technology, processing conditions, dose basis and target sample when requesting an asphalt pigment candidate. A successful color match alone cannot qualify a repair for road service.
Technical references
- Procter Johnson: Colouring Asphalt
- Shell: Clear-binder asphalt and aggregate example
- HA Italia: Distinct aggregate-based asphalt pigment specifications
Independent technical guidance used for this application overview. These references are not FUXIN project case studies or a substitute for a grade-specific technical data sheet.
